Add comments for Aloha (#417)

Co-authored-by: Simon Alibert <75076266+aliberts@users.noreply.github.com>
这个提交包含在:
Remi
2024-09-06 21:07:52 +02:00
提交者 GitHub
父节点 d6516f0e03
当前提交 9ff829a3a1
共有 4 个文件被更改,包括 38 次插入 和 6 次删除

查看文件

@ -41,6 +41,13 @@ Or using `poetry`:
poetry install --sync --extras "dynamixel"
```
/!\ For Linux only, ffmpeg and opencv requires conda install for now. Run this exact sequence of commands:
```bash
conda install -c conda-forge ffmpeg
pip uninstall opencv-python
conda install -c conda-forge opencv>=4.10.0
```
You are now ready to plug the 5V power supply to the motor bus of the leader arm (the smaller one) since all its motors only require 5V.
Then plug the 12V power supply to the motor bus of the follower arm. It has two motors that need 12V, and the rest will be powered with 5V through the voltage convertor.

查看文件

@ -496,6 +496,17 @@ class ManipulatorRobot:
# Set a velocity limit of 131 as advised by Trossen Robotics
self.follower_arms[name].write("Velocity_Limit", 131)
# Use 'extended position mode' for all motors except gripper, because in joint mode the servos can't
# rotate more than 360 degrees (from 0 to 4095) And some mistake can happen while assembling the arm,
# you could end up with a servo with a position 0 or 4095 at a crucial point See [
# https://emanual.robotis.com/docs/en/dxl/x/x_series/#operating-mode11]
all_motors_except_gripper = [
name for name in self.follower_arms[name].motor_names if name != "gripper"
]
if len(all_motors_except_gripper) > 0:
# 4 corresponds to Extended Position on Aloha motors
self.follower_arms[name].write("Operating_Mode", 4, all_motors_except_gripper)
# Use 'position control current based' for follower gripper to be limited by the limit of the current.
# It can grasp an object without forcing too much even tho,
# it's goal position is a complete grasp (both gripper fingers are ordered to join and reach a touch).

查看文件

@ -1,13 +1,19 @@
import platform
import time
def busy_wait(seconds):
# Significantly more accurate than `time.sleep`, and mandatory for our use case,
# but it consumes CPU cycles.
# TODO(rcadene): find an alternative: from python 11, time.sleep is precise
end_time = time.perf_counter() + seconds
while time.perf_counter() < end_time:
pass
if platform.system() == "Darwin":
# On Mac, `time.sleep` is not accurate and we need to use this while loop trick,
# but it consumes CPU cycles.
# TODO(rcadene): find an alternative: from python 11, time.sleep is precise
end_time = time.perf_counter() + seconds
while time.perf_counter() < end_time:
pass
else:
# On Linux time.sleep is accurate
if seconds > 0:
time.sleep(seconds)
class RobotDeviceNotConnectedError(Exception):

查看文件

@ -1,3 +1,11 @@
# Aloha: A Low-Cost Hardware for Bimanual Teleoperation
# https://aloha-2.github.io
# https://www.trossenrobotics.com/aloha-stationary
# Requires installing extras packages
# With pip: `pip install -e ".[dynamixel intelrealsense]"`
# With poetry: `poetry install --sync --extras "dynamixel intelrealsense"`
_target_: lerobot.common.robot_devices.robots.manipulator.ManipulatorRobot
robot_type: aloha
# Specific to Aloha, LeRobot comes with default calibration files. Assuming the motors have been